I posted earlier this week about problems connecting to ftp servers from a
laptop which is running through my RedHat box to the Internet. I have
uncommented a couple lines on my firewall script as advised, but I am still
having problems as follows:

If I try to use IE for FTP I get:
200 type set to A
500 Invalid port command
500 LPRT 6,16,0,0,0,0,0,0,0,0,255,255,255,255,232,241,2,2,10,7 command not
understood

If I use a Dos window I seem to connect, but when I do a "ls" I
get "invalid port"


I have included the script I am using. Please be detailed with any
instruction.


-- 
Raymond Norton
Little Crow Telemedia Network
320-234-0270

-------------- next part --------------
#!/bin/sh
#
# rc.firewall - Initial SIMPLE IP Firewall script for Linux 2.4.x and iptables
#
# Copyright (C) 2001  Oskar Andreasson <blueflux at koffein.net>
#
# This program is free software; you can redistribute it and/or modify
# it under the terms of the GNU General Public License as published by
# the Free Software Foundation; version 2 of the License.
#
# This program is distributed in the hope that it will be useful,
# but WITHOUT ANY WARRANTY; without even the implied warranty of
# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
# GNU General Public License for more details.
#
# You should have received a copy of the GNU General Public License
# along with this program or from the site that you downloaded it
# from; if not, write to the Free Software Foundation, Inc., 59 Temple
# Place, Suite 330, Boston, MA  02111-1307   USA
#

###########################################################################
#
# 1. Configuration options.
#

###########################################################################
#
# Local Area Network configuration.
#
# your LAN's IP range and localhost IP. /24 means to only use the first 24 
# bits of the 32 bit IP adress. the same as netmask 255.255.255.0
#

LAN_IP="192.168.0.1"
LAN_IP_RANGE="192.168.0.0/24"
LAN_BCAST_ADRESS="192.168.255.255"
LAN_IFACE="eth1"

###########################################################################
#
# Localhost Configuration.
#

LO_IFACE="lo"
LO_IP="127.0.0.1"

###########################################################################
#
# Internet Configuration.
#

INET_IP=""
INET_IFACE="eth0"

###########################################################################
#
# IPTables Configuration.
#

IPTABLES="/sbin/iptables"

###########################################################################
#
# 2. Module loading.
#

#
# Needed to initially load modules
#
/sbin/depmod -a

#
# Adds some iptables targets like LOG, REJECT and MASQUARADE.
#
/sbin/modprobe ip_conntrack
/sbin/modprobe ip_tables
/sbin/modprobe iptable_filter
/sbin/modprobe iptable_mangle
/sbin/modprobe iptable_nat
/sbin/modprobe ipt_LOG
#/sbin/modprobe ipt_REJECT
#/sbin/modprobe ipt_MASQUERADE

#
# Support for owner matching
#
#/sbin/modprobe ipt_owner

#
# Support for connection tracking of FTP and IRC.
#
/sbin/modprobe ip_conntrack_ftp
/sbin/modprobe ip_conntrack_irc


###########################################################################
#
# 3. /proc set up.
#
# Enable ip_forward if you have two or more networks, including the
# Internet, that needs forwarding of packets through this box. This is
# critical since it is turned off as default in Linux.
#

echo "1" > /proc/sys/net/ipv4/ip_forward

#
# Dynamic IP users:
#
#echo "1" > /proc/sys/net/ipv4/ip_dynaddr

###########################################################################
#
# 4. IPTables rules set up.
#
# Set default policies for the INPUT, FORWARD and OUTPUT chains.
#

$IPTABLES -P INPUT DROP
$IPTABLES -P OUTPUT DROP
$IPTABLES -P FORWARD DROP

#
# bad_tcp_packets chain
#
# Take care of bad TCP packets that we don't want.
#

$IPTABLES -N bad_tcp_packets
$IPTABLES -A bad_tcp_packets -p tcp ! --syn -m state --state NEW -j LOG \
--log-prefix "New not syn:"
$IPTABLES -A bad_tcp_packets -p tcp ! --syn -m state --state NEW -j DROP

#
# Do some checks for obviously spoofed IP's
#

$IPTABLES -A bad_tcp_packets -i $INET_IFACE -s 192.168.0.0/16 -j DROP
$IPTABLES -A bad_tcp_packets -i $INET_IFACE -s 10.0.0.0/8 -j DROP
$IPTABLES -A bad_tcp_packets -i $INET_IFACE -s 172.16.0.0/12 -j DROP

#
# Enable simple IP Forwarding and Network Address Translation
#

$IPTABLES -t nat -A POSTROUTING -o $INET_IFACE -j SNAT --to-source $INET_IP

#
# Bad TCP packets we don't want
#

$IPTABLES -A FORWARD -p tcp -j bad_tcp_packets

#
# Accept the packets we actually want to forward
#

$IPTABLES -A FORWARD -i $LAN_IFACE -j ACCEPT
$IPTABLES -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A FORWARD -m limit --limit 3/minute --limit-burst 3 -j LOG \
--log-level DEBUG --log-prefix "IPT FORWARD packet died: "

#
# Create separate chains for ICMP, TCP and UDP to traverse
#

$IPTABLES -N icmp_packets
$IPTABLES -N tcp_packets
$IPTABLES -N udpincoming_packets

#
# The allowed chain for TCP connections
#

$IPTABLES -N allowed
$IPTABLES -A allowed -p TCP --syn -j ACCEPT
$IPTABLES -A allowed -p TCP -m state --state ESTABLISHED,RELATED -j ACCEPT
$IPTABLES -A allowed -p TCP -j DROP

#
# ICMP rules
#

# Changed rules totally
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 8 -j ACCEPT
$IPTABLES -A icmp_packets -p ICMP -s 0/0 --icmp-type 11 -j ACCEPT

#
# TCP rules
#

$IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 21 -j allowed
$IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 22 -j allowed
$IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 80 -j allowed
$IPTABLES -A tcp_packets -p TCP -s 0/0 --dport 113 -j allowed

#
# UDP ports
#

# nondocumented commenting out of these rules
#$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 53 -j ACCEPT
#$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 123 -j ACCEPT
$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 2074 -j ACCEPT
$IPTABLES -A udpincoming_packets -p UDP -s 0/0 --source-port 4000 -j ACCEPT

##########################
# INPUT chain
#
# Bad TCP packets we don't want.
#

$IPTABLES -A INPUT -p tcp -j bad_tcp_packets

#
# Rules for incoming packets from the internet.
#

$IPTABLES -A INPUT -p ICMP -i $INET_IFACE -j icmp_packets
$IPTABLES -A INPUT -p TCP -i $INET_IFACE -j tcp_packets
$IPTABLES -A INPUT -p UDP -i $INET_IFACE -j udpincoming_packets

#
# Rules for special networks not part of the Internet
#

$IPTABLES -A INPUT -p ALL -i $LAN_IFACE -d $LAN_BCAST_ADRESS -j ACCEPT
$IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $LO_IP -j ACCEPT
$IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $LAN_IP -j ACCEPT
$IPTABLES -A INPUT -p ALL -i $LO_IFACE -s $INET_IP -j ACCEPT
$IPTABLES -A INPUT -p ALL -i $LAN_IFACE -s $LAN_IP_RANGE -j ACCEPT
$IPTABLES -A INPUT -p ALL -d $INET_IP -m state --state ESTABLISHED,RELATED \
-j ACCEPT
$IPTABLES -A INPUT -m limit --limit 3/minute --limit-burst 3 -j LOG \
--log-level DEBUG --log-prefix "IPT INPUT packet died: "

###############################
# OUTPUT chain
#
#
# Bad TCP packets we don't want.
#

$IPTABLES -A OUTPUT -p tcp -j bad_tcp_packets

#
# Special OUTPUT rules to decide which IP's to allow.
#

$IPTABLES -A OUTPUT -p ALL -s $LO_IP -j ACCEPT
$IPTABLES -A OUTPUT -p ALL -s $LAN_IP -j ACCEPT
$IPTABLES -A OUTPUT -p ALL -s $INET_IP -j ACCEPT

#
# Log weird packets that don't match the above.
#

$IPTABLES -A OUTPUT -m limit --limit 3/minute --limit-burst 3 -j LOG \
--log-level DEBUG --log-prefix "IPT OUTPUT packet died: "