There are no jumpers on this ASUS board, Ken. If you read the rest of the thread you’d see we covered all of these items… > On Jul 19, 2015, at 7:29 PM, Kenneth Lynes <kenlynes at usa.net> wrote: > > Hi Brian, I was expecting to be at the meeting Sat but could not come. I can > tell you this: Do Not short out the cmos jumpers with the power supply on! > You are to move the jumper from its present setting of 1-2 to 2-3 for a few > moments and then put the jumper back on 1-2. > This is a pretty common configuration. > I just hope you have not done any harm to the cmos by shorting pins. You may > be lucky and done it while no power was supplied to the motherboard as it > would be if up and running. > If you look up the motherboard on line and download the manual it will > probably tell you the codes for the leds that you see. Not sure what 00 would > be but it is probably either saying no cpu or a ram problem. > Normally a board will boot up or post with ram in either of the two slots but > some require ram in both slots or in a case where there are 4 slots to be in > at least two of them. > Check to see your cpu is in place as suggested before and then before putting > on the cpu fan and heatsink, be sure to use the cpu grease as required. I also > wonder if you did plug in the set of wires which plug into the motherboard > near the cpu. These are the ones labeled as going to the cpu from the power > supply. At least a plug with 4 wires on it but in most later mb's it is > usually 6 or 8 wires. > You can call me if you wish. I am in Mpls 612-331-7429 > Ken > > ------ Original Message ------ > Received: Sun, 19 Jul 2015 12:00:14 PM CDT > From: tclug-list-request at mn-linux.org > To: tclug-list at mn-linux.org > Subject: tclug-list Digest, Vol 127, Issue 20 > >> Send tclug-list mailing list submissions to >> tclug-list at mn-linux.org >> >> To subscribe or unsubscribe via the World Wide Web, visit >> http://mailman.mn-linux.org/mailman/listinfo/tclug-list >> or, via email, send a message with subject or body 'help' to >> tclug-list-request at mn-linux.org >> >> You can reach the person managing the list at >> tclug-list-owner at mn-linux.org >> >> When replying, please edit your Subject line so it is more specific >> than "Re: Contents of tclug-list digest..." >> >> >> Today's Topics: >> >> 1. Re: Problem building system (Brian Wood) >> 2. Re: Solder skills / equip / tomato capable router? (Dan Armbrust) >> >> >> ---------------------------------------------------------------------- >> >> Message: 1 >> Date: Sat, 18 Jul 2015 13:39:12 -0500 >> From: Brian Wood <woodbrian77 at gmail.com> >> To: tclug-list <tclug-list at mn-linux.org> >> Subject: Re: [tclug-list] Problem building system >> Message-ID: >> <CABWFOjsfs61-74yjVws30sDZc21G4AhqC+=mhGz4H931eKJB9Q at mail.gmail.com> >> Content-Type: text/plain; charset="utf-8" >> >> Previously I wrote: >>> I saw that there were two things inside of a white circle and >>> it said "clrmos2" or something like that, but I wasn't sure what >>> to do with those two things and still don't know. >> >> I figured out from some duckduckgoing that I could clear >> the cmos by using a screwdriver and touching those two >> things at the same time. I tried that several times and still >> got the "00" code after it booted. Another time when I was >> touching those things with the screwdriver, the machine turned >> on by itself without me pushing the power button, but that >> resulted in the same thing. >> >> One thought I had was taking the cpu over to someone's >> with an lga 1150 motherboard. I wouldn't mind letting you >> put the cpu in place. I'm hoping to get some good news and >> find that at least the cpu is fine. Any volunteers? >> >> -- >> Brian >> Ebenezer Enterprises >> http://webEbenezer.net >> -------------- next part -------------- > > _______________________________________________ > TCLUG Mailing List - Minneapolis/St. Paul, Minnesota > tclug-list at mn-linux.org > http://mailman.mn-linux.org/mailman/listinfo/tclug-list